7 Most Common Problems with New Holland WorkMaster 60

New Holland’s WorkMaster series is a great utility tractor, especially the WorkMaster 60. It’s durable, economical, and easy to use. The horsepower is enough to handle the work of your harvesting land. However, you might face some New Holland WorkMaster 60 problems after using it for a few months.

The most common issues of a New Holland WorkMaster 60 are faulty hydraulic system, low RPM throttle, and PTO doesn’t functioning. You might also face problems like loss of hydraulic pressure, no starter power, the tractor doesn’t turn over, and random beeping noise.

It will be challenging to drive your WorkMaster if you don’t fix the problems or take immediate action. Sometimes you might have permanent damage due to these issues.

Quick Table for New Holland WorkMaster 60 Problems, Reasons, Symptoms, and Solutions

Reading the details is boring! Well, you have this short table to look at the problems, symptoms, and solutions of your New Holland WorkMaster 60. But hey! Don’t forget to check on the details later.

7 Common New Holland WorkMaster 60 Problems, Reasons, Symptoms, and Solutions:

Machines can show errors, and you can’t ignore those issues. Even though you maintain the tractor properly, there will always be some problems. So, it would help if you learn about the common issues and the best ways to deal with them.

1. Loss of Hydraulic Pressure

Hydraulic pressure is needed in the brakes and gear clutches. So, if there’s a loss of hydraulic pressure, you should immediately stop driving your WorkMaster and fix the issue.

Symptoms:

When there’s something unusual about the hydraulic pressure on your tractor, you need to observe closely to ensure the signs.

• Not enough strength to control the brake
• Loose pressure on hydraulic brake
• Hydraulic oil is leaking

Reasons:

You should not ride your new Holland WorkMaster when there’s no hydraulic pressure. So, locate the causes quickly and take action.

• Loose connections at the hydraulic system
• Oil leakage from the hydraulic lines
• Broken brake pads

Solutions:

Don’t just sit there after you find the reasons. Take necessary measures to deal with the loose hydraulic pressure. You can start with:

• Adjust and repairing the wire connections
• Checking the brake pads
• Repair the leakages of the pipelines

2. Low RPM Throttle

You might think that there are no problems when your new Holland shows poor performance. But believe us, there’s something serious going on, and you need to investigate.

Symptoms:

It won’t be too tough to figure out the signs of low RPM. All you need to do is just don’t ignore the blatant symptoms like:

• Poor performance
• Doesn’t have enough power like usual to run the tractor
• Take extra time to start the engine

Reasons:

As showing low RPM throttle is not a good sign, you need to find out the reasons as soon as you can. Here are some possible causes:

• Low battery voltage
• Near empty fuel tank
• Faulty ignition coil
• Air gap in the ignition coil
• Loose wire connections

Solutions:

Low RPM is dangerous to your engine. It might damage the shaft, cylinder, or valves. You can apply these suggestions and save your engine:

• Check and charge the battery
• Fill the fuel tank
• Check the wire connections
• Repair or replace the ignition coil
• Adjust the gap of the ignition coil
• Check the display alerts before checking the wires

3. PTO Is Not Working

The power take-off stub is one of the crucial parts of your New Holland tractor because it transfers the power to the machine. So, when there’s a problem with the PTO, how can you drive without fixing it!

Symptoms:

When your PTO doesn’t function, you will notice the following signs and always make a list of them.

• Loose connections around the sensor
• Failed to develop full power if the engine

Reasons:

Typically, the new engine doesn’t show problems with the PTO. If your machine has a couple of months or years on it, you might face PTO problems. Here are some causes behind it:

• Loose wire connections
• Faulty sensors
• Old power shaft
• Lose nut bolts of the sensor

Solutions:

Fix your PTO problems quickly. Otherwise, your tractor won’t work correctly and provide the output you want. Here are the methods you can try:

• Repair the wire connections
• Check the sensors and replace them if needed
• Change the power shaft
• Adjust the nut bolts adjacent to the sensor

4. Tractor Doesn’t Turn Over

It’s one of the prevalent issues with the tractors. You are trying to start the new Holland WorkMaster, and it’s not turning over. Well, you are not the only one with this issue.

Symptoms:

You don’t need to struggle to locate the signs of such a problem. You would simply notice:

• Problem with the starter
• Can’t start the engine
• Failed to turn the tractor

Reasons:

As it’s not expected that your tractor is not to turn over, you need to search for the causes so that you can take action against them. Here are the common reasons:

• Fail to turn the tractor
• Problems with controlling speed
• Problems with the starter

Solutions:

If your new Holland tractor is not turning over, you need to deal with it as soon as possible, or else your harvesting work might get late. Here are the techniques you can try:

• Check the battery charge
• Repair the wire connection
• Check the ignition coil and adjust the air gap
• Check the starter solenoid and safety switch

5. No Power to Starter

When your tractor is not starting, the starter might have a problem. So, you need to observe the problem and fix the issue.

Symptoms:

Of course, there will be some symptoms whenever you have issues with the starter. Here are some common signs:

• Struggling to start the engine
• Showing no power at the starter

Reasons:

How can you deal with the problems if you can’t locate the causes? So, find out the reasons and then take necessary measures.

• Faulty safety lock system
• Damaged wire connections
• Defective main fuse
• Faulty clutch

Solutions:

List out the problems! Follow these methods to resolve the issue and ride your tractor smoothly again.

• Check the safety lock system
• Repair the wire connections
• Replace the main fuse
• Install a new clutch

6. Faulty Hydraulic System

Hydraulic fluid is necessary for brakes, clutch, and other vital parts. If there’s something wrong with the hydraulic system, your tractor may have brake failure or other malfunctions.

Symptoms:

Sometimes, it may seem tricky to realize a problem with the hydraulic system. So, observe carefully and make a list of the signs.

• Hydraulic fluid leaks
• White fluid emits from the pump or hydraulic cylinder

Reasons:

The hydraulic system is a crucial part of the engine. You need to locate the reasons behind a faulty hydraulic system.

• Leakages in the pipes
• Faulty hydraulic pump
• Low-grade hydraulic oil

Solutions:

If you don’t want a messed-up hydraulic system in your New Holland tractor fix the issues right away. Here’s what you do:

• Repair the leakages in the pipelines
• Check the hydraulic pump and cylinder
• Add new hydraulic oil

7. Random Beeping Noise

Heard some beeping noise but couldn’t find the source? It happens due to some internal issues in your WorkMaster. Fix this annoying sound right away.

Symptoms:

Well, don’t struggle to find the signs in this case. You will only notice signs like

• Random beeping noise
• No lights or codes during the beeping

Reasons:

Though it’s not that serious, it’s more like an annoying problem. So, locate the causes and fix them. Here are some possible reasons:

• Faulty sensors
• Loose connection around the specific parts

Solutions:

If you want to get rid of this annoying noise, take some immediate measures such as:

• Check the sensors and repair them
• Repair the wire connections
• Check the noises are genuine or not

FAQs

What’s the power of Holland WorkMaster 60?

The WorkMaster series of New Holland is defined by its horsepower. That means the WorkMaster 60 has 60 horsepower or 44.7 kilowatts.

But in reality, the outcomes are a bit lower than the claimed one. According to the PTO claim, it can deliver 51 horsepower or 38 kilowatts.

What engines are used in New Holland tractors?

The New Holland tractors use the ECOBlue HI-e SCR Cursor 9 engines. It’s a high-efficiency selective catalytic reduction engine.

What’s the cost of a New Holland WorkMaster?

A new Holland WorkMaster tractor can cost you between $18000 and $30000 based on the model.

Conclusion

New Holland’s WorkMaster series is pretty popular among farmers and professionals. The tractors are full of features and provide a smooth experience. But sometimes, these tractors have some bothersome issues that need to be dealt with to save the engine from damage.

Hopefully, the discussion on New Holland WorkMaster 60 problems has proven helpful to you. You can deal with them whenever you face such issues by following our guidelines. It will assist you in maintaining your unique experiences with the New Holland tractor. Wish you good luck with your ride!

Related Posts: