Most Common Problems with John Deere 333E (Solutions Added)

John Deere makes incredible mowers, tractors, skid steers, etc. and 333e is one of the best products of the company. It has good user reviews and great performance.

But sometimes, some users faced a few issues like a hydraulic problem, bucket lifting malfunction, etc. which can be troublesome at some point. It may also show some issues with control responsiveness.

Hence, you should know what to do if you find yourself in that kind of situation. In this article, I will help you with those answers and share the solution to John Deere 333e problems.

Problems and Solutions at a Glance

3 Common John Deere 333e Problems and Their Solutions:

John Deere 333e has some easy to solution problems which you may face while working. Here are some of them-

1. Hydraulic Problem

John Deere 333e has hydraulic problems which were found by only a few users. But you can be one of them if you are unlucky.

Here are the main problems of this hydraulic issue-

• Whenever hydraulic fluid is left idling for an extended amount of time, it can end up losing many of its important properties, which can lead to difficulties with transmission.
• Cavitation, which happens if there is air accessible in the system, has the potential to cause issues with the hydrostatic transmission. This possibility exists because of the following:
• Whenever you attempt to drive the 333e with a belt that is too damaged, you should definitely hear a loud crackling sound. Should it be damaged, you will be unable to travel in any direction at all.
• If the transmission gears are not correctly greased, they may become difficult to use and become slow.
• If the oil pipes on the skid are leaking, you might just have problems moving the skid forward.

• Temperatures that are too high within the hydraulic system are a frequent cause for concern. It is in your best interest to steer clear of employing heated hydraulic systems if you want to prevent oil leaking.
• Furthermore, hydraulic systems that are put in jeopardy by being exposed to freezing temperatures run the risk of failing, which can be costly.

The Fix:

An extensive investigation of the system is required in order to focus on the fundamental issue that is causing the trouble.

If you can determine what caused the issue with the hydraulic system, repairing it shouldn’t be too difficult of a task.

• Before moving on, you need to verify there is neither air nor water mixed together anywhere in the system.
• Perform a thorough inspection of the inside components in order to search for any indications of damage. It is necessary to replace any components that you find to be damaged in some way.

It is strongly recommended that you check the fluid level in the front axle at least once every 8 hours.

The hydraulic fluid has to be changed after the first few hours of use, which is the minimum amount of time recommended for its lifespan.

• You should also make the adjustment after one hundred hours have passed. A typical issue that arises when the skid does not receive an adequate supply of fluid refill is dullness.
• Skids that move at a very slow pace could present a risk. When you use them too quickly, you put yourself in danger of having an accident.
• While operating the skid, you should attempt to keep the temperature as standard as you possibly can.

2. Bucket lift and tilt stopping

There are plenty of reasons why the bucket is having lifting or tilting issues. you have to try and find the correct issue to solve it.

• Whenever the bucket stops operating, you should check the safety switch. Due to safety switches malfunction, the bucket stops raising or tilting at irregular intervals.
• Bucket parts are lubricated and heated to resist overheating by hydraulic fluid, which is accountable for heat dissipation. Additional benefits include preventing pollution and corrosion by sealing the gaps.

Therefore, if the skid’s hydraulic fluid level drops, the bucket’s joints will not be properly lubricated, resulting in poor performance.

• The bucket’s performance can be restricted by problems with the solenoid and wiring. This necessitates a thorough examination of the wire cluster
• Because the bucket is frequently used, it is possible that the nuts and bolts holding it in place have become loose. To assure appropriate tilting and lifting, examine them and fix them if necessary.
• A further factor contributing to the bucket’s failure to raise and tilt is the connector locking levers’ lack of capacity to fully close. This problem develops when there is a disturbance in the pin alignment on a large number of occasions. It is the responsibility of the pin alignment to set the parts and align the bucket.

The Fix:

If the problem is with the safety switch, the only way to solve the problem is to have new safety switches installed in place of the old ones.

When the hydraulic fluid is the issue, it has been recommended that you replenish the reservoir with fresh hydraulic fluid.

In addition, check to see that the hydraulic system does not have any leaks or parts that do not fit properly, as this can cause fluid to escape from the system.

Moreover, to make sure that the tank contains the appropriate amount of hydraulic fluid, you should not fill this to an excessive level.

If the solenoid is the issue here, you should probably change it because it cannot be repaired in most cases.

It is essential that you get the bolts and nuts changed as soon as possible if they are rusted in order to restore the bucket to its best level of performance.

The problem with the pin alignment is rather serious, as it should require you to unscrew the bucket section to access the levers and pin alignments. Because of this, it is highly recommended that you contact a mechanic and ask him to adjust the pin alignment for you.

3. Controls Unresponsive

There are occasions in which users discover that the controls for the 333e skid steer’s steering and loader are not reacting to their directional inputs.

These problems can occasionally be traced back to steering or loader connections that have become detached or have become slack, in which case you will need to reconnect or strengthen them.

The Fix: 

It is recommended that you examine the wires that are connected to the control panel and confirm that they are connected correctly. The cables join the actuators and the hydraulic pump.

In some instances, if you are unable to resolve the issue through the use of alternative methods, you may be required to change the complete circuit board of the control panel.

What Majority of the Users Feel about John Deere 333e?

The majority of the users have never faced problems with the JD 333e model. It is one of the cleanest products of John Deere. Only a few users have ever found any problem.

One user mentioned that he loved using this loader and has been using it for a long time now. It was easy to use and after using it for this long period he never faced any serious trouble. But there were some wear-offs due to use.

But one user reported the hydraulic problem but others never found it in their 333e.

Another user said the controls are not quite responsive as they should be. But that was not a major issue for him because it was very comfortable and easy to use.

Frequently Asked Questions

Final Thoughts

John Deere 333e is one of the best of the e-series. It does not have lots of problems that you may face and you should enjoy a really great time using it. However, if you ever find any of the above-mentioned John Deere 333e problems, you can follow the instructions given in this article for solving them. I hope it helps you.

Related Posts: