6 Common Problems with John Deere 2355 & Their Solutions
John Deere 2355 is one of the 55 Utility Series tractors by John Deere. It ran from 1987 to 1992. It comes with a 3.9L 4-cylinder diesel. Although this has been a great little utility tractor, it does come with certain issues.
The most common John Deere 2355 problem includes a bad start, non-disengaging PTO, sticky brakes, clutch issues, hydraulic problems, loader and 3-pt hitch trembling under heavier weights, steering problem etc.
In this article, I will discuss all these problems and their solutions. By the end, you will be an expert on the JD 2355 troubleshooting. So gear up for managing all your tractor problems right now!
Problems and Solutions at a Glance:
| Problems with John Deere 2355 | Solutions |
| Poor Start | Troubleshooting. |
| PTO Not Disengaging | Split the PTO clutch. |
| Sticky Brakes | Replace damaged valves, and troubleshoot. |
| Clutch Issues | Bleed the clutch master. |
| Hydraulic Problems | Various troubleshooting and replacements. |
| Loader and Hitch Vibrating | Look for leakages or blown hydraulic parts and troubleshoot. |
6 Most Common Problems with John Deere 2355 and Their Possible Solutions:
Users have reported some common John Deere 2355 problems. Here are some of those problems and how to solve them.
1. Poor Start
A common problem in these tractors is not starting after letting to sit for some time. Unless you jump the solenoid, they don’t start. The tractor is prone to stopping after running for a while.
Often, you won’t be able to jump either. You might hear the started click. But the tractor will not start.
The Fix:
There can be many reasons for a tractor to behave this way. Therefore, many troubleshooting tips exist!
If you want quick fixes, you can try having the clutch pedal down and the shift levers in the neutral position. In addition to that, check for blown fuses. Usually, the fuses 5 or 6 are more prone to blowing.
A blown fuse cuts off the solenoids. Other than that the solenoids can get damaged due to other reasons. Corroded and dirty connections, bad relay switch being a few reasons why the tractor will not start.
For a more accurate fix, here’s what to do : The neutral start switch and the instrument cluster are connected by two short cables with connections. One of the wires may have an infinite resistance (can be found in testing).
You may also discover a cold solder junction. Repair this wire with new connectors and you are good to go.
2. PTO Not Disengaging
PTO does not disengage and runs all the time. With this cab, it is pretty frequent. And a very complicated thing to fix.
The PTO clutch rubs and gets corroded. This makes it run all the time.
The Fix:
To address this issue, people may suggest you to check PTO pressure. But it is not always accurate. To replace the clutch or check it, you will need to remove the cab entirely.
The clutch needs to be split. And to split it, you’ll need to access the area behind the clutch housing, which requires removing the cab.
The cab might possibly be propped and the problem solved underneath. There are hidden bolts in the shifter cover. With these bolts, you can remove the axle housing as well.
3. Sticky Brakes
The John Deere 2355 could experience stuck brakes. Neither wheel will spin when the tractor’s rear is raised as if it were in gear. There appears to be no reaction when you use the parking brake.
When the tractors get warmer, the steering and brakes both may dysfunction.
The Fix:
This tractor has no power brakes, so the pressure you put on it is all you get. The equalizer valve, piston check valve, and wheel piston o-ring all have the potential to leak.
You can test for wheel packing leakage by plugging the line and looking for a hard pedal. If you find one, the wheel packing is bad. If you don’t, its probably the equalizer valve.
4. Clutch Issues
This problem mainly concerns shifting issues. When the clutch is still disengaged, the tractor creeps forward and occasionally has difficulty shifting gears. The shifter may also be difficult to change into gear without a grinding sound.
The Fix:
Bleed the clutch master or the slave cylinders of the clutch. Check the free travel adjustment of the clutch pedal as well. Assuming the clutch is engaged and the sticks are in netural, begin by simultaneously engaging the clutch and the sticks.
5. Hydraulic Problems
The typical symptom is the loader dying out or stopping. The 3-pt hitch and hydraulics also seem to have no activity. You might notice the steering still being fine.
Sometimes, the PTO too goes out with the power link and the power steering.
The Fix:
You could attempt to destroke the hydraulics. The steering will be the last to go since the priority valve will keep it operating until the end.
In addition, inspect filters and draw the strainer on the rear end if the brakes are breaking down because this will clog the strainer and limit flow. You can also check for damage of the stroke control valve.
The bolts could have backed out or the rubber coupler between the front pulley and the pump could have ruptured. Check them and do the necessary troubleshooting.
6. Loader and Hitch Vibrating
Sometimes the loader and lift both trembles, even when the loader is under less pressure than a threshold. For example, when raising the loader and the lift, both begin to come down.
Along with the shuddering, the hydraulic oil level may run correctly. However, you may still notice some oil spillages under the loader valve. This indicates leakage.
The Fix:
This is a pretty common issue. It mostly occurs due to lack of hydraulic oil. If you have filled up hydraulic oil recently, it may occur due to leakages somewhere.
Typically a hydraulic hose can get blown. The O-ring may get blown inside. For this, you will have to split tractor.
What Majority of the Users Feel?
The John Deere 2355 is said by several owners to perform above expectations on farms. Even at 55 horsepower, they are capable of much more. It is an excellent tractor that is simple to operate and maintain.
A 146 loader with an 84″ wide bucket is included on this one. You can remove woof chips with this big container. The 7-foot rotary cutter on this tractor is primarily used for cutting grass.
Although 7 foot implements often choke down the tractors with single blade. A 175 loader is quite perfect with a patch of land and cattle. This can carry about 1500 lbs.
The tractor comes with dry clutch, which some owners regret. This one’s great for haying or mowing as such.
And in this case, the 55 series tractors from Mannheim are considered by many, the best series ever made. The 2555 is one of this series.
The speed at which your implement drops is controlled by a hydraulics knob. So that you don’t ram things into the ground too quickly and break things. Overall, the owners are mostly satisfied with it than have complaints.
Frequently Asked Questions
What is the fuel filter part number on the JD 2355?
Part Number AR50041.
When to change the fuel filter on John Deere 2355?
Every 600 hours.
How much does the collarshift transmission weight on the JD 2355?
36L.
Final Thoughts
After research, I can say that it is a great tractor! However, a better option can be the 2955 or the 2555. Overall, this tractor has lesser nuances than known. So you can go with it for good performance in an economical tractor.
Related Posts: